WDMA Store: Window, Entry Door and Skylight Standards

Back to Store

WDMA T.M. 14-21 Clear and Pigmented Coatings for Interior Prefinished Wood

WDMA T.M. 14-21, Test Method for Factory Applied Clear and Pigmented Coatings for Interior Prefinished Wood and Wood Cellulosic Composites Used for Millwork provides a nationally recognized guideline for the performance recommendation and evaluation procedures for Factory Applied Clear and Pigmented Coatings on interior wood and cellulosic composites for millwork products. It will serve as a basis of common understanding for producers, distributors, and users. It will also promote fair competition within the industry and assist purchasers and end users in obtaining properly coated millwork.

Once purchased, you will receive an electronic version of the document.

Price: $6.00
Sign in for member price

Purchase

WDMA T.M. 11-21 Pigmented Primer Coatings

WDMA T.M. 11-21, Test Method for Factory Applied Pigmented Primer Coatings for Wood and Wood Cellulosic Composites Used for Millwork provides a nationally recognized guideline for the performance recommendations and evaluation procedures for Factory Applied Pigmented Primer Coatings on exterior wood and cellulosic composites for millwork products.

Once purchased, you will receive an electronic version of the document.

Price: $6.00
Sign in for member price

Purchase

AAMA/WDMA/CSA 101/I.S.2/A440-17 North American Fenestration Standard

The 2017 edition of AAMA/WDMA/CSA 101/I.S.2/A440, NAFS — North American Fenestration Standard/Specification for windows, doors, and skylights is the third edition of the standard, and supersedes the previous edition published in 2011 under the same title.

This standard is jointly published by the American Architectural Manufacturers Association (AAMA), the Window and Door Manufacturers Association (WDMA), and the Canadian Standards Association (CSA). This Standard/Specification is applicable for use in testing and rating windows, doors, secondary storm products (SSPs), tubular daylighting devices (TDDs), roof windows, and unit skylights, and represents the continuing development of an internationally accepted performance Standard/Specification for all windows, doors, SSPs, TDDs, roof windows, and unit skylights.

Once purchased, you will receive an electronic version of the document.

View the table of contents.

Price: $80.00
Sign in for member price

Purchase

AAMA/WDMA/CSA 101/I.S.2/A440-11 North American Fenestration Standard

The 2011 edition of AAMA/WDMA/CSA 101/I.S.2/A440, NAFS — North American Fenestration Standard/Specification for windows, doors, and skylights is the third edition of the standard, and supersedes the previous edition published in 2008 under the same title.

This standard is jointly published by the American Architectural Manufacturers Association (AAMA), the Window and Door Manufacturers Association (WDMA), and the Canadian Standards Association (CSA). This Standard/Specification is applicable for use in testing and rating windows, doors, secondary storm products (SSPs), tubular daylighting devices (TDDs), roof windows, and unit skylights, and represents the continuing development of an internationally accepted performance Standard/Specification for all windows, doors, SSPs, TDDs, roof windows, and unit skylights.

This edition includes all errata, as of January 2017.

Once purchased, you will receive an electronic version of the document.

View the table of contents.

Price: $80.00
Sign in for member price

Purchase

User guide to AAMA/WDMA/CSA 101/I.,S.2/A440 NAFS 2011

This is the first edition of the User guide to AAMA/WDMA/CSA 101/I.S.2/A440, NAFS 2011 — North American Fenestration Standard/Specification for windows, doors, and skylights. It is jointly published by the American Architectural Manufacturers Association (AAMA), the Window & Door Manufacturers Association (WDMA), and CSA Group.

Intended users of NAFS include code officials, manufacturers, architects, engineers, consumers, builders, contractors, trade associations, test labs, specifiers, and government agencies. This user guide is intended to provide those users with guidance for the proper application of NAFS. It contains informative commentary, illustrations, and examples to help answer some of the more common questions associated with NAFS.

Once purchased, you will receive an electronic version of the document.

Price: $40.00
Sign in for member price

Purchase

WDMA I.S. 4-19 Industry Specification for Preservative Treatment for Millwork

WDMA I.S. 4-19 Industry Specification for Preservative Treatment for Millwork provides a nationally recognized standard for the water-repellent preservative treatment for millwork and serves as a basis of common understanding for producers, preservative formulators, distributors and users. The Standard is also intended to promote fair competition within the industry and to aid purchasers and users in obtaining properly treated millwork. This latest edition contains additional requirements for formulation product approval.

PDF Download

View the table of contents and scope.

Price: $10.00
Sign in for member price

Purchase

WDMA I.S. 10-19 Industry Specification for Testing Cellulosic Composite Material

WDMA I.S. 10-19 Industry Specification for Testing Cellulosic Composite Materials for Use in Fenestration Products applies to composite materials that will be used in the manufacture of fenestration products. It provides a common test basis for composite materials used in the manufacture of fenestration products.

Once purchased, you will receive an electronic version of the document.

View the table of contents and scope.

Price: $6.00
Sign in for member price

Purchase

WDMA I.S. 11-18 Analytical Method for Design Pressure Rating of Fenestration

WDMA I.S.11-18 Analytical Method for Design Pressure Rating of Fenestration Products describes analytical methods for obtaining design pressure ("DP") ratings of fenestration products of sizes other than that of a tested specimen or specimens. For purposes of compliance with this document, DP ratings shall be permitted in increments of no less than one psf.

Once purchased, you will receive an electronic version of the document. The document will be sent as a PDF, with an Excel attachment embedded.

View the table of contents and scope.

Price: $12.00
Sign in for member price

Purchase

WDMA T.M. 12-20 Pigmented Finishes Test

WDMA T.M. 12-20 , "Test Method for Factory Applied Pigmented Finish Coatings for Wood and Wood Cellulosic Composites Used for Millwork", is available for purchasing on the WDMA Online Bookstore. This test method has been revised by the Material and Supplier Technical Committee to incorporate the most up to date content, provisions and best practices that improve the test procedures and alignment with other recognized industry practices for film thickness, adhesion resistance and color uniformity. These changes improve the test method to create a more uniform guideline for the performance recommendations and clarifies the evaluation procedures for Factory Applied Pigmented Coatings on exterior wood and cellulosic composites for millwork products.

Once purchased, you will receive an electronic version of the document.

View the table of contents and scope.

Price: $6.00
Sign in for member price

Purchase

WDMA T.M. 13-19 Method for Preparing Retention and Penetration Testing Samples

WDMA T.M. 13-19 Method for Preparing Retention and Penetration Testing Samples provides a nationally recognized guideline for the performance recommendation and evaluation procedures for Factory Applied Pigmented Coatings on exterior wood and cellulosic composites for millwork products.

Once purchased, you will receive an electronic version of the document.

View the scope.

Price: $6.00
Sign in for member price

Purchase

WDMA T.M. 14-13 Clear and Pigmented Coatings for Interior Prefinished Wood

WDMA T.M. 14-13 , Test Method for Factory Applied Clear and Pigmented Coatings for Interior Prefinished Wood and Wood Cellulosic Composites Used for Millwork provides a nationally recognized guideline for the performance recommendation and evaluation procedures for Factory Applied Clear and Pigmented Coatings on interior wood and cellulosic composites for millwork products. It will serve as a basis of common understanding for producers, distributors, and users. It will also promote fair competition within the industry and assist purchasers and end users in obtaining properly coated millwork.

Once purchased, you will receive an electronic version of the document.

View the scope.

Price: $6.00
Sign in for member price

Purchase

Cold Weather Condensation Brochure

Cold Weather Condensation is a new brochure published by WDMA that discusses the circumstances under which condensation can appear on windows during cold weather, and describes methods may reduce the likelihood or severity of this happening. This brochure contains updated indoor relative humidity recommendations, the major reason for condensation on windows and within building components. The brochure is intended as a technical discussion for building owners and occupants.

Once purchased, you will receive an electronic version of the document.

Price: $5.00
Sign in for member price

Purchase

FMA/WDMA 250-10 Installation of Non-Frontal Flange Windows with Mounting Flanges

FMA/WDMA 250-10 Standard Practice for the Installation of Non-Frontal Flange Windows with Mounting Flanges for Surface Barrier Masonry Construction for Extreme Wind/Water Conditions is jointly published by WDMA and the Fenestration Manufacturers Associatiion (FMA). It covers the installation of non-frontal-flanged windows in new construction surface barrier masonry wall buildings of no more than three stories in height. This practice applies to non-frontal flanged windows which employ an integral or applied mounting flange that is attached and sealed to the window perimeter frame designed as an appendage that will cover a previously-installed buck and/or integrate with a pre-formed sill. This standard covers the installation process for windows from pre- to post-installation.

Once purchased, you will receive an electronic version of the document.

View the scope.

Price: $30.00
Sign in for member price

Purchase

FMA/AAMA/WDMA 300-12 Installation of Exterior Doors in Wood Frame Construction

FMA/AAMA/WDMA 300-12, Standard Practice for the Installation of Exterior Doors in Wood Frame Construction for Extreme Wind/Water Exposure is jointly published by WDMA and the Fenestration Manufacturers Associatiion (FMA) and the Architectural Aluminum Manufacturers Association (AAMA). It covers the installation of exterior doors with mounting flanges, exterior casing/brick molding, and box frame/non-flanged mounting attachments in new construction residential and light commercial buildings utilizing a membrane/drainage system. Installation methods that are consistent with this document have been water tested up to a test pressure of 575 Pa (12 psf) using the ASTM E547 water test.

Once purchased, you will receive an electronic version of the document.

View the scope.

Price: $30.00

Purchase

FMA/AAMA/WDMA 400-13 Installation of Exterior Doors in Surface Barrier Masonry

FMA/AAMA/WDMA 400-13 Standard Practice for the Installation of Exterior Doors in Surface Barrier Masonry Construction for Extreme Wind/Water Exposure is jointly published by WDMA and the Fenestration Manufacturers Association (FMA) and the Architectural Aluminum Manufacturers Association (AAMA). It covers the installation of exterior doors with mounting flanges, exterior casing/brick molding, and box frame/non-flanged mounting attachments in new construction residential and light commercial buildings utilizing a membrane/drainage system. Installation methods that are consistent with this document have been water tested up to a test pressure of 575 Pa (12 psf) using the ASTM E547 water test.

Once purchased, you will receive an electronic version of the document.

Price: $30.00

Purchase

FMA/AAMA/WDMA 2710-20 UL Brick Veneer Window Replacement Guide

FMA/AAMA/WDMA 2710-20, Guidelines for the Full Frame Replacement of Windows without Removal of Exterior Brick Veneer, covers the replacement of windows in residential and light commercial buildings of not more than three stories above grade in height, utilizing a membrane/drainage system, a surface barrier drainage or a wall system without a reliable membrane drainage system. The guideline is focused on the full frame replacement without removal of external brick veneer. This document describes methods where the cavity between the wall and façade needs to be blocked and sealed. It is the responsibility of the installer to determine if this document is applicable to the replacement project, though the assistance of a design professional may be necessary if the existing water management system is found to be defective or inefficient. This guideline does not address any water management concerns beyond the window installation.

Once purchased, you will receive an electronic version of the document. The document will be sent as a PDF attachment embedded.

View the table of contents and scope.

Price: $30.00
Sign in for member price

Purchase

FMA/AAMA/WDMA 500-16 Installation of Mounting Flange Windows in FPIS Walls

FMA/AAMA/WDMA 500-16 Standard Practice for the Installation of Mounting Flange Windows into Walls Utilizing Foam Plastic Insulating Sheathing (FPIS) with a Separate Water-Resistive Barrier (WTB) is jointly published by WDMA and the Fenestration Manufacturers Association (FMA) and the Architectural Aluminum Manufacturers Association (AAMA). It covers the installation of windows into walls utilizing foam plastic insulating sheathing (FPIS); and addresses installations for residential and light commercial buildings of not more than three stories above grade plane in height. This standard practice is to address: attachment and continuous support of the window and water management principles for windows installed with FPIS.

Once purchased, you will receive an electronic version of the document.

View the scope.

Price: $30.00

Purchase

Errata to AAMA/WDMA/CSA 101/IS2/A440-11

This document identifies the errata to 101/I.S.2/A440-11 officially approved by AAMA, WDMA and CSA in March 2014. This errata supplements the original published edition of the standard.

To see a list of those sections that have been modified, click here.

Price: $0.00

Purchase

WDMA T.M. 1-14 Soil Block Test

WDMA T.M. 1-14 Test Method to Determine Preservative Effectiveness in Preventing Wood Decay evaluates the relative wood preservative effectiveness by means of a laboratory soil block culture. Results of this test are used to recognize commercial millwork preservatives as meeting the requirements of WDMA I.S.4 Water Repellent Preservative Treatment for Millwork. This standard replaces WDMA T.M 1-94 (06).

View the table of contents and scope.

Price: $6.00
Sign in for member price

Purchase

WDMA T.M. 2-15 Swellometer Test

WDMA T.M. 2-15 Test Method to Determine the Short-term Anti-swell Effectiveness of Treating Systems is designed to measure the effectiveness of water-repellents in millwork preservative formulations in retarding dimensional changes of wood exposed to water. This test method is also used for determining if a commercial millwork preservative meets the requirements of WDMA I.S.4 Water-Repellent Preservative Treatment for Millwork.

PDF Download

View the scope.

Price: $6.00
Sign in for member price

Purchase

WDMA T.M. 11-14 Pigmented Primer Coatings

WDMA T.M. 11-14 Test Method for Factory Applied Pigmented Primer Coatings for Wood and Wood Cellulosic Composites Used for Millwork provides a nationally recognized guideline for the performance recommendations and evaluation procedures for Factory Applied Pigmented Primer Coatings on exterior wood and cellulosic composites for millwork products.

PDF Download

View the scope.

Price: $6.00
Sign in for member price

Purchase

AAMA/WDMA/CSA 101/I.S.2/A440-08 (updated) Windows, Doors and Unit Skylights

Updated Edition -- May 2008 (contains errata and updates to the initial 2008 release)

Jointly developed by representatives from the American Architectural Manufacturers Association (AAMA), the Canadian Standards Association (CSA) and the Window and Door Manufacturers Association (WDMA), this is the first truly harmonized North American Window standard. This Standard/Specification incorporates the basic content of the previous editions; AAMA/NWWDA 101/l.S.2-97, Voluntary Specification for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors; AAMA/WDMA 1600/I.S.7, Voluntary Specification for Skylights; AAMA/WDMA 101/I.S.2/NAFS-05, Voluntary Performance Specification for Windows, Unit Skylights, and Glass Doors; CAN/CSA-440-00/CSA A440.1-00, Windows/User Selection Guide to CSA Standard and CAN/CSA-A440-00, Windows. (Includes May 2008 and September 2008 Updates.)

PDF Download

View the table of contents.

Price: $60.00
Sign in for member price

Purchase

Errata AAMA/WDMA/CSA 101/I.S.2/A440-08 - May 2008 and September 2008

This document identifies the errata to 101/I.S.2/A440-08 officially approved by AAMA, WDMA and CSA in May 2008 and September 2008. This errata supplements the original published edition of the standard.

Price: $0.00

Purchase

AAMA/WDMA/CSA 101/I.S.2/A440-05 (updated) windows, doors and unit skylights

Updated Edition -- May 2007 (contains errata and updates to the 2005 edition)

Jointly developed by representatives from the American Architectural Manufacturers Association (AAMA), the Canadian Standards Association (CSA) and the Window and Door Manufacturers Association (WDMA), this is the first truly harmonized North American Window standard. This Standard/Specification incorporates the basic content of the previous editions; AAMA/NWWDA 101/l.S.2-97, Voluntary Specification for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors; AAMA/WDMA 1600/I.S.7, Voluntary Specification for Skylights; AAMA/WDMA 101/I.S.2/NAFS-02, Voluntary Performance Specification for Windows, Unit Skylights, and Glass Doors; CAN/CSA-440-00/CSA A440.1-00, Windows/User Selection Guide to CSA Standard and CAN/CSA-A440-00, Windows. This Standard/Specification also incorporates several significant changes and new requirements for products not previously covered, including requirements for side-hinged exterior doors. Other highlights include the introduction of a limited water rating for side-hinged doors; expansion of the product rating system; revision of gateway requirements; introduction of cycle/operating testing for side-hinged doors; introduction of hardware water testing for doors; introduction of vertical load testing for doors; introduction of forced entry resistance testing for doors; and the addition of new sash, frame and glazing material requirements.

PDF Download

View the table of contents.

Price: $45.00
Sign in for member price

Purchase

Errata AAMA/WDMA/CSA 101/I.S.2/A440-05- May 2007

This document identifies the errata and updates officially approved by AAMA, WDMA and CSA in May 2007, to 101/I.S.2/A440-05. The errata uses strikeout and underline to identify the changes. This document can be used to suplement older edtions of the standard.

PDF Download

Price: $0.00

Purchase

ANSI/AAMA/WDMA 101/I.S.2/NAFS-02 Windows, Skylights and Glass Doors

This standard has been developed to bring closer harmony between the various windows standards in North America, as well as incorporating significant improvements and additions to the 101/IS 2 standard. It is the result of close work between WDMA, AAMA, the Canadian Window & Door Manufacturers Association (CWDMA) and the Canadian Standards Association (CSA). Like the 101/IS 2 standard, NAFS-02 is a performance-based standard which includes total unit, material and component performance requirements. The addition of skylights, specialty products, side lites and transoms to the standard brings the total number of operating types recognized in the standard to 26.

PDF Download

View the table of contents.

Price: $40.00
Sign in for member price

Purchase

AAMA/WDMA 1600/I.S. 7-00 Voluntary Specification for Skylights

AAMA/WDMA 1600/I.S. 7-00 Voluntary Specification for Skylights establishes recognized performance requirements for materials, construction and assembly of complete factory glazed, glass or plastic skylights for both residential and commercial construction.

PDF Download

View the table of contents.

Price: $6.00
Sign in for member price

Purchase

ANSI/AAMA/NWWDA 101/I.S.2-97 Aluminum, Vinyl (PVC), Wood Windows and Glass Doors

This standard will give the specifier or architect a single source from which to specify windows and glass doors. The requirements for all types of windows and glass doors have been combined into one national performance based standard which includes total unit, material and component performance requirements. The Voluntary Specification for Windows and Glass Doors establishes performance standards suitable for a majority of project applications. This standard combined the following standards into one document: NWWDA I.S.-2 for Wood Window Units, I.S.-3 for Wood Sliding Patio Doors and I.S.-8 for Wood Swinging Doors.

PDF Download

Price: $25.00
Sign in for member price

Purchase

Back to Store